Specifications
| Cooling scheme | Air-cooling type |
|---|---|
| Control models | Dehumidification |
| Cooling capacity(W) | 4200/4800 |
| Thermal capacity(W) | 7200/7800 |
| Temperature stability(℃) | ±0.1 |
| Setting Temperature Range(℃) | 20 to 30 |
| Humidity stability(%RH) | ±0.5％ |
| Setting Humidity Range(%RH) | DP4.5℃～OA or less |
| Use Area Temperature(℃) | 15～35 (Temperature change gradient: Within 1℃/1h) |
| Use Area Humidity(%RH) | 15～85 (Humidity change gradient: within 5%RH/1h) (No condensation) |
| Processed air volume(m3/min) | 5.0～20.0／6.0～22.0 |
| External Dimensions(mm) | H1631×W650×D800 |
| Weight(kg) | 220 |
| Coating Color | Ivory (Y22-85B semi-gloss) |
| Blower duct connection diameter(mm) | φ200 (with damper) |
| Rated voltage(V) | Three-phase AC 200 |
| Consumption Current(A) | 12/12（Rated） 13/14（MAX） |
| Consumption wattage(W) | 3300/3900（Rated） 3700/4600（MAX） |
| Drain connection diameter | 20A female socket (Rp: 3/4 inch) |
| Refrigerant(g) | R407C 1500g |
| Exhaust air volume(m3/min) | 33.4/39.2 |
| Safety circuit / Main circuit | Earth leakage breaker (20A 30mA), reverse rotation prevention relay |
| Safety circuit / Blower | Overcurrent relay, delay timer (3 minutes), surge absorber |
| Safety circuit / Compressor | High and low pressure abnormal pressure protection, overcurrent relay, motor protector, surge absorber, cooling water freeze protection, cooler freeze/superheat protection |
| Output/Main unit abnormal output | Normal close/no-voltage (250 VAC/5 A/resistive load) |
| Output / Temperature upper / Lower limit alarm | Normal close/no-voltage (240 VAC/1 A/resistive load) |
*Cooling capacity is the value at the main unit blowout port at an ambient temperature of 27 ℃/70％RH and processing air flow of 5/6 ㎥/min. Cooling capacity is 6400/7000 W at a processing flow rate of 20/22 ㎥/min.
* The temperature and humidity control accuracy is based on the method prescribed in JTMK01 Constant Temperature Humidistat Bath – Performance Testing Method and Performance Display Method (Japan Testing Machine Association). Only the value indicated by the temperature controller built into the air conditioner at the main unit blow off port is guaranteed to be accurate and thermal interference due to the duct etc. is not covered by the precision guarantee. In addition, the purpose of this product is to suppress temperature fluctuations in the air and so the absolute value of the temperature is not guaranteed. (A bias function for compensation is built into the system.)
*The temperature and humidity may not be controllable even if they are within the set range depending on the ambient temperature and humidity.
*Be sure to set the humidity lower than the ambient humidity. In addition, the temperature and humidity may not be controllable even if they are within the set range depending on the ambient temperature and humidity.
*Processing air flow value is taken at the main unit blowout port.
*The above-mentioned dimensions are the dimensions of the main unit. The mounting flange and protrusions are excluded.
*The consumption current and power consumption indicated are maximum values. These fluctuate depending on the temperature and humidity of the ambient environment and the operating conditions.
*Waste heat is discharged from the device because it is air-cooled. (with optional exhaust chamber)
*When the ambient temperature drops below the operating ambient temperature, a protection device is activated to automatically stop only the compressor. Since the above-mentioned accuracy cannot be guaranteed in this case, use the equipment within the range of operating ambient temperatures.
・For the actual installation, check the specifications and precautions stated in the instruction manual.
・Contact our nearest sales office if you need an instruction manual in advance for design purposes.
External dimensions
[Caution]To ensure proper operation of this equipment, read the operation manual before use.
Depending on model and quantity, separate charter delivery may be arranged (additional costs apply).
Overseas at the time of delivery, we recommend packing for overseas separately.
After verifying the specifications, insert an appropriate breaker (circuit breaker for wiring) between the product and power supply.
Cause of failure and be used at the rated power supply out of range.
Please use the service and maintenance on a regular basis.
Failure to maintain regular maintenance, you may be a factor in product performance degradation trouble.
When disposing of this product, you should comply with various laws and regulations, please go to the appropriate.
