| Brand | SHIMPO |
|---|---|
| Sub Categories | Mass, Force & Hardness Test and Measurements |
| Application | Motorized Test Stands for Force Gauges |
By changing digital force gauges (push-pull gauges), loads ranging from 2 N to 2,500 N can be measured with this force gauge stand. The USB interface and specialized FGT-VC add-in software, which is available free of charge, allow the stand carriage moving distance and load data to be easily transferred to a computer and displayed as a graph.
A wider range of loads
Loads ranging from 2 to 2,500 N (0.2-250 kg) can be measured. Various types of digital force gauges can be mounted.
Note: Digital force gauges are sold separately.
 |
 |
 |
| FGP Series | FGPX Series | FGPX-H Series |
(Digital force gauges other than the FGP Series listed above can be mounted as well. However, please note that separate adapter plates are required to mount them.)
・Longer stroke
The mounted force gauge can be moved by up to 400 mm to perform various types of tests.
・Wider speed range
The wide travel speed range (10-400 mm/min) allows the force gauge to respond to various test conditions.
Easy to use
・Uses an LCD on the operation panel
Key switch layout for easy operation
・For switching operation modes
・For setting travel speed
・For displaying distance and travel speed
| Output |  |
|---|---|
| Load capacity | 1000 N (100 kg), 2500 N (kg) |
| Connectivity |  |
| Supportable force gauges | FGP Series, FGPX Series, FGPX-H Series |
USB connection
Distance and loads are displayed as graphs
Specialized FGT-VC software enables measurement data to be easily transferred to a personal computer. The stand carriage moving distance and the force gauge load data can be simultaneously transferred.
* The FGT-VC data transfer software specially prepared for the FGS-VC digital force gauge stands is available for download. Click on the Software Download link below to move to the download page.
| Model | FGS-100VC | FGS-250VC | |
|---|---|---|---|
| Measured load | 1000N（100kgf） | 2500N（250kgf） | |
| Load capacity | 1000N（100kgf） | 2500N（250kgf） | |
| Feed rate | 10~400mm/min Set the speed on the operation panel |
||
| Stroke | 400mm | ||
| Representation Department | Dot matrix LCD signed 4 digits | ||
| Display | Movement speed display | 10~400mm/min | |
| Distance traveled display | 0.0～400.0mm | ||
| Display the number of repetitions | 0～9999 | ||
| Mode of operation | MANU mode: Move to dog/JOG mode: Inching operation/SING mode: 1 move between DOGs CONT mode: Repeat movement between dogs / PROG mode: Move position at 5 points |
||
| Correspondence | USB | USB (for PC) | |
| Input | Overload Input | Stop at overload signal of FGPX (FGP) | |
| Measurement table | 150×200mm | ||
| Operating temperature range | 0~45°C (non-condensing) | ||
| Power supply | AC100V±10％ | ||
| Mass | Approx. 63kg | Approx. 65kg | |
| Accessory | With power supply AC socket for force gauge, connection cable for FGPX (FGP), USB cable | ||
| PC Software | Free download from the symposium website | ||
| Send load and distance data, display graphs With trigger function (data acquisition starts after reaching the set load) The number of continuous data acquisitions can be set / With upper and lower limit judgment function |
|||
| Other | Emergency stop switch | ||
| Compatible Force Gauge | FGP-0.2～50,100 | FGP-0.2～50,100 | |
| FGPX-0.2～50,100 | FGPX-0.2～50,100 | ||
| FGPX-250H | |||
FGS-100VC
FGS-250VC
Test and Measurements
Test and Measurements
Test and Measurements
Test and Measurements
Test and Measurements
Test and Measurements
Test and Measurements
Test and Measurements
