A new standard created by listening to our customers. A wider range of test requirements and higher test speciﬁcations.
A-series meets the needs for such a versatile test environment.
Advanced automatic energy saving, high level of functionality and a protected test environment.
A series improves the working environment of vibration testing.

Features

1. Improvement of performance

Improvement in excitation force

When compared with the conventional i & J series, the A series increases the relative excitation force.

・Increased force per system power requirement
・Increased force per system mass
・Increased force per system size

Improvement in excitation force

When compared with the conventional i- & J-series, the A-series has increased relative excitation force.

Standard 76.2 mmp-p displacement *Only for A30, A45, A65, A74

A-series has a displacement of 76.2 mmp-p (3-inch stroke), which provides a good balance within the specifications for velocity, acceleration and displacement. This single system can be used for a very wide variety of tests.

Increase in frequency range

In addition to the increased displacement of 76.2 mmp-p, the maximum frequency range is also increased when compared to the i- and J-series.

Introduction of new power module

By developing a power amplifier that uses a new next generation Silicon Carbide power module, IMV has achieved low noise and high efficiency. This new power module is standard-issue for all A-series models.

2. User friendly and Secure

Advanced automatic energy saving, high level of functionality and a protected test environment. A-series provides a better working environment for vibration testing.

Lower power consumption

In comparison with the same class of conventional systems (i,J-series), the A-series achieves lower power consumption. With an automatic energy-saving function increased energy saving is achieved across all force ranges.

International safety standards

A-series complies with international safety standards

3. User friendly principle

Rapid creation of a test from a set of pre-defined templates conforming to most international test standards.

LAUNCHER

Test file will be automatically generated upon selection of the test conditions defined by the test standards. Then, the test can be carried out just by pressing the start button.

In-built “Quick Help” provides guidance on each operation.

SYSTEM MONITOR

Statuses for vibration generator, amplifier test proceeding, and specimen can be observed on a PC or tablet by either wired or wireless LAN. Solutions can be seen on the Web browser upon the occurrence of any error. Installation of additional software is not necessary for PC or tablet.

Home screen

Home screen (error)

Eco screen

Camera screen

Manual link screen

Standard

System Model				Unit	A11/SA1HAG	A22/SA2HAG	A30/SA3HAG	A45/SA4HAG	A65/SA5HAG
System Specifications	Frequency Range			Hz	0－4500	0－3300	0－2600	0－2600	0－2600
	Rated Force	Sine		kN	11	22	30	45	65
		Random		kN rms	11	22	30	45	65
		Shock		kN	22	44	60	90	130
	Maximum Acc.	Sine		m/s²	1	1	900	900	900
		Random		m/s² rms	630	630	630	630	630
		Shock		m/s² peak	2	2	1,818	1,8	1,806
	Maximum Vel.	Sine		m/s	2.0	2.0	2.0	2.0	2.0
	Maximum Vel.	Shock		m/s peak	2.5	2.5	2.5	2.5	2.5
	Maximum Disp. (Sine)			mmp-p	51	51	76.2	76.2	76.2
	Maximum Travel			mmp-p	64	64	82	82	82
	Maximum Load			kg	200	300	400	600	1
	Power Requirements			kVA	20.4	30	36	57	83
	Breaker Capacity			A	75	100	125	200	300
Vibration Generator	Model				A11	A22	A30	A45	A65
	Armature Mass			kg	11	22	33	50	72
	Armature Diameter			φmm	210	280	290	436	446
	Allowable Eccentric Moment			N・m	294	700	850	1,55	1,55
	Dimensions	Width		mm	946	1,038	1,1	1,232	1,31
		Height		mm	827	955	1,048	1,215	1,253
		Depth		mm	676	775	840	1,04	1,04
	Shaker Body Diameter			φmm	585	678	725	825	925
	Mass			kg	1,08	1,6	2	3	4,2
Power Amplifier	Model				SA1HAG-A11	SA2HAG-A22	SA3HAG-A30	SA4HAG-A45	SA5HAG-A65
	Maximum Output			kVA	12	24	31	44	68
	Dimensions	Width		mm	580	580	580	580	580
		Height		mm	1,95	1,95	1,95	1,95	1,95
		Depth		mm	850	850	850	850	850
	Mass			kg	280	350	520	900	1
Controller	Vibration Controller				See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2
Cooling	Cooling Method				Air cooling	Air cooling	Air cooling	Air cooling	Air cooling
	Blower	Dimensions	Width	mm	606	707	707	1,057	1,214
			Height	mm	1,315	1,531	1,531	1,841	2,006
			Depth	mm	891	917	917	1,125	1,124
		Mass		kg	125	210	210	250	420
		Wattage		kw	3.7	5.5	5.5	11	18.5
		Duct Hose Diameter		φ	125	200	200	250	250

*Random force ratings are specified in accordance with ISO5344 conditions. Please contact IMV or your local distributor with specific test requirements.

*Power supply: 3-phase 200/220/380/400/415 V (A74 is only AC380/400/415 V), 50/60 Hz. A transformer is required for other supply voltages.

*Breaker capacity for AC 200 V.

*Above 4000 Hz, the force rolls-off at a rate of -6 dB/oct.

*Above 2000 Hz, the force rolls-off at a rate of -12 dB/oct.

*Specification above applies to 60 Hz. Dimensions change for 50 Hz.

*An export license is required for exporting the shaker system of over 50 kN sine force.

*The specification shows the maximum system performance. For long-duration tests, system must be de-rated up to 70%.

Continuous use at maximum levels may cause failure. Please contact IMV if your system operates at more than 70%.

*For random vibration tests, please set the test definition of the peak value of acceleration waveform to operate at less than the maximum acceleration of shock.

*Frequency range values vary according to the sensor and vibration controller.

*Armature mass and acceleration may change when a chamber is added.

*Mass and dimensions may change for CE-marked systems.

ECO

System Model				Unit	A11/EM1HAG	A22/EM2HAG	A30/EM3HAG	A45/EM4HAG	A65/EM5HAG	A74/EM6HAG	A74/EM8HAG
System Specifications	Frequency Range			Hz	0－4500	0－3300	0－2600	0－2600	0－2600	0－2600	0－2600
	Rated Force	Sine		kN	11	22	30	45	65	74	74
		Random		kN rms	11	22	30	45	65	74	74
		Shock		kN	22	44	60	90	130	148	180
		High Velocity Shock		kN	16.5	36	50	80	120	120	160
	Maximum Acc.	Sine		m/s²	1	1	900	900	900	1	1
		Random		m/s² rms	630	630	630	630	630	630	630
		Shock		m/s² peak	2	2	1,818	1,8	1,806	2	2
		High Velocity Shock		m/s² peak	1,5	1,636	1,515	1,6	1,666	1,621	2
	Maximum Vel.	Sine		m/s	2.0	2.0	2.0	2.0	2.0	2.0	2.0
		Shock		m/s peak	2.5	2.5	2.5	2.5	2.5	2.5	2.5
		High Velocity Shock		m/s peak	3.5	3.5	3.5	3.5	3.5	3.5	3.5
	Maximum Disp.	Sine		mmp-p	51	51	76.2	76.2	76.2	76.2	76.2
		High Velocity Shock		mmp-p	55	55	76.2	76.2	76.2	76.2	76.2
	Maximum Travel			mmp-p	64	64	82	82	82	82	82
	Maximum Load			kg	200	300	400	600	1	1	1
	Power Requirements			kVA	20.4	30	36	57	83	100	100
	Breaker Capacity			A	75	100	125	200	300	250	250
Vibration Generator	Model				A11	A22	A30	A45	A65	A74	A74
	Armature Mass			kg	11	22	33	50	72	74	74
	Armature Diameter			φmm	210	280	290	436	446	446	446
	Allowable Eccentric Moment			N・m	294	700	850	1,55	1,55	1,55	1,55
	Dimensions	Width		mm	946	1,038	1,1	1,232	1,31	1,31	1,31
		Height		mm	827	955	1,048	1,215	1,253	1,253	1,253
		Depth		mm	676	775	840	1,04	1,04	1,04	1,04
	Shaker Body Diameter			φmm	585	678	725	825	925	925	925
	Mass			kg	1,08	1,6	2	3	4,2	4,8	4,8
Power Amplifier	Model				EM1HAG-A11	EM2HAG-A22	EM3HAG-A30	EM4HAG-A45	EM5HAG-A65	EM6HAG-A74	EM8HAG-A74
	Maximum Output			kVA	12	24	31	44	68	100	100
	Dimensions	Width		mm	580	580	580	1,16	1,16	1,16	1,16
		Height		mm	1,95	1,95	1,95	1,95	1,95	1,95	1,95
		Depth		mm	850	850	850	850	850	850	850
	Mass			kg	470	560	590	1	1,15	1,34	1,85
Controller	Vibration Controller				See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2	See Vibration Controller K2
Cooling	Cooling Method				Air cooling	Air cooling	Air cooling	Air cooling	Air cooling	Air cooling	Air cooling
	Blower	Dimensions	Width	mm	708	707	707	1,169	1,128	1,462	1,462
			Height	mm	1,421	1,531	1,531	2,123	2,38	2,8	2,8
			Depth	mm	782	917	917	799	899	927	927
		Mass		kg	140	210	210	280	228	320	320
		Wattage		kw	3.7	5.5	5.5	11	18.5	30	30
		Duct Hose Diameter		φ	125	200	200	250	250	250	250

*Random force ratings are specified in accordance with ISO5344 conditions. Please contact IMV or your local distributor with specific test requirements.

*Power supply: 3-phase 200/220/380/400/415 V (A74 is only AC380/400/415 V), 50/60 Hz. A transformer is required for other supply voltages.

*Breaker capacity for AC 200 V.

*Breaker capacity for AC 400 V.