SV-A Series Tuning Fork Vibro Viscometers

Brand	AND
Sub Categories	Material Inspection and Analysis
Application	Viscometer

Danh mục: Kiểm tra và Đo lường

DESCRIPTION

2 ml Sample Measurement Now Possible!

Features

2 ml sample measurement (SV-1A)

Anti-corrosive, titanium sensor plates and temperature sensor

X-Y-Z stage for fine position adjustment of the sample cup

Wide-range, continuous measurement without replacing the sensor plates

Simultaneous measurements of temperature and viscosity

Windows Communication Tools WinCT-Viscosity and a serial-USB converter provided as standard

Easy set up and very quick measurement

Excellent repeatability (1% of the measured value by standard deviation)

Extremely high sensitivity (detects a viscosity as low as 0.3 mPa·s)

Little interference to the sample fluid

Possible to measure fluids in motion

Simplified calibration function (for SV-1A and SV-10A)

Easy cleaning after measurement

Videos

External Input / Output

RS-232C interface

Accessories

Click here to see the complete accessory list.


Standard Cup Set for SV-1A （AX-SV-55)	Standard Cup Set for SV-10A/100A (AX-SV-54)

Example Measurements with the Tuning Fork Vibro Viscometer (SV/SV-A Series)

The SV-10/SV-10A series of tuning fork vibro viscometers are capable of continuous measurement over a range of viscosities from the extremely low (0.3 mPa·s) to the high (10,000 mPa·s).
These viscometers are able to easily measure the state transition from sol to gel as there is no need to change sensors during measurement.
Measurement intervals can be set freely allowing for continuous 24-hour measurement or measurement of any long term viscosity change.

Gel transition / hydrogel measurement
Example) Aqueous gelatin solutionThis example shows viscosity measurement of 2.5% and 5% aqueous gelatin solutions over varying temperature.
The horizontal axis shows temperature and the vertical axis shows a logarithm of the viscosity of the aqueous gelatin solutions. There is a clear difference in solidification temperature which is dependent on the concentrations of the aqueous gelatin solutions. Gel transition

Cloud point measurement
Example) Non-ionic surfactant

This is the result of a measurement taken while a 1% concentration of a non-ionic surfactant was heated. Surfactants become cloudy when they reach a certain temperature. This is called the cloud point and traditionally could only be measured optically.
However, a rapid change in viscosity occurs at the cloud point and this change can be measured with the SV-10A.
From this graph of temperature vs. viscosity we can see that a rapid change in viscosity occurs at 35.4˚C. This temperature is taken as the cloud point. This non-ionic surfactant is defined to have a cloud point at 35.9˚C according to JIS standards, demonstrating that the SV-10A is capable of cloud point measurement.

Cloud point measurement

Rapid Rise in Viscosity (Measurement of the curing point)
Example) Egg whites

As egg whites are heated to 60˚C their viscosity will decrease like normal liquids. However, once 60˚ is reached viscosity will increase suddenly, as the proteins in the egg whites clump together.
The SV-A series of vibro viscometers can accurately capture small changes specific to a certain substance as well as dynamic changes in viscosity.
As shown in the graph below made with WinCT-Viscosity (RsVisco), viscosity can be displayed as a logarithm allowing for simple, easy-to-understand graphical representation when viscosity change covers a large area or for non-linear changes.

rapid rise in viscosity

Measurements at low viscosity
Example) Measuring the viscosity of varying concentrations of aqueous ethanol solutions.

The viscosity of varying concentrations of aqueous ethanol solutions at 25˚C was measured with the SV-10A. Viscosity of these solutions was shown to vary with concentration. Alone, both 100% ethanol and 100% water have low viscosities but when they are mixed viscosity increases.

Measurements at low viscosity

WinCT-Viscosity data processing software

WinCT-Viscosity is dedicated software that makes realtime graphs of data acquired from the SV Series and SV-A Series viscometers (WinCT-Viscosity supports Windows 8). WinCT-Viscosity allows for simple reading, storage, and analysis of measurement data acquired from SV viscometers. WinCT-Viscosity is comprised of three programs.

Graphing with WinCT-Viscosity (RsVisco)

1. The time axis： Track variation over time
2. Identify temperature dependency： Find a correlation between temperature and viscosity
3. Focus on specific values： Easily select min and max values for the X/Y axes
4. Convert to Excel file： Convert a file with a CSV extension to Excel for preparing documents

Example) Engine Oil

1. Variation over time
2. Temperature dependency

Engine oil

Example) Thickening Agent

1. Overall numerical value change
2. Using min/max to focus on specific values

Thickening agent

It is possible to expand a designated section of the Ｘ and Ｙ axes. Double click to overwrite the value.
Example) Expansion of the viscosity range between 80-100ｍPa·s for the first three minutes of measurement.
→ Double click the maximum value (shown as 30 on the graph) of the X axis (time) and enter 3.
→ On the y axis (viscosity) double click the minimum value (shown as 0 on the graph) and change to 80, double click the maximum value (shown as 500) and change to 100.
⇒ A graph of the designated area will be displayed.

SPECIFICATION

Model	SV-1A	SV-10A	SV-100A
Measurement method	Tuning fork vibro method (natural frequency at 30Hz)
Viscosity measurement unit	mPa·s, Pa·s, cP, P		Pa·s, P
Viscosity measurement range	0.3 to 1000 mPa·s	0.3 to 10000 mPa·s	1 to 100 Pa·s
Repeatability (standard deviation)	1% of the measured value (20 to 30°C, no condensation)
Minimum sample amount	2 ml	10 ml
Temperature measurement	0 to 160°C / 0.1°C(32 to 320°F/0.1°F)
Display	Vacuum Fluorescent Display (VFD)
Power supply / consumption	AC adapter / approx. 14 VA (including the AC adapter)
External dimensions / weight	Main unit: 112 (W) × 132 (D) × 291(H) mm / approx. 0.8 kg
	Display unit: 238 (W) × 132 (D) × 170(H) mm / approx. 1.3 kg
Standard accessories	Stand for securing the sensor unit, X-Y-Z stage, cup set Software set (including a serial-USB converter) AC adapter, connection cable (1.5 m), carrying case