• English
    • Deutsch
    • French
    • Requires WPML plugin
  • Country
    • United States (USD)
    • Deutschland (EUR)
    • Japan (JPY)
FREE SHIPPING FOR ALL ORDERS OF $150
0 items / $0.00
Login / Register
  • Newsletter
  • Contact Us
  • FAQs
  • Home
  • About us
  • Products
  • Partners
  • Services
  • Customers
  • Recruit
  • Contact us
Vietnamese
Menu
Home Test and Measurements ESI SR1050 SERIES 1M & 10 M RESISTANCE TRANSFER STANDARD
Digital Insulation Tester MY600
Back to products
Digital Earth Tester EY200
Click to enlarge
IET Labs, Inc

ESI SR1050 SERIES 1M & 10 M RESISTANCE TRANSFER STANDARD

Brand

IET Labs, Inc

Sub Categories

Lab tools

Application

Standard Resistor

Category: Test and Measurements
Share:
close
YOU MAY ALSO LIKE…
  • No.1840-00 Min-Max Digital Thermometer PC-3510
  • No.1830-00 Refrigerator Digital Thermometer PC-3310
  • No.1758-00 Waterproof Digital Thermometer PC-9235
  • No. 1756-00 waterproof digital thermometer PC-9230
  • GENERAL
  • DESCRIPTION
  • SPECIFICATION
  • DATASHEET AND MANUAL
  • APPLICATION NOTES AND SOFTWARE
  • ACCESSORIES
GENERAL

GENERAL

  • Resistance Values 1 MΩ & 10 MΩ
  • Initial Accuracy… ± 25 or 30 ppm of nominal value matched within 10 ppm
  • Transfer Accuracy… ± 2 ppm (Typical Short-term Repeatability)
  • Calibration Accuracy… ± 10 or 15 ppm
DESCRIPTION

DESCRIPTION

For low resistance transfer standards, consider the esi SR1010 or SR1030

IET Labs continues to manufacture the SR1050 to the same exacting specs as esi/Tegam

Introduction
Each of the esi SR1050 transfer standards consists of 11 equal steps. These steps are available in increments of 1M Ω, (SR1050-1M) and 10M Ω, (SR1050-10M). The esi SR1050 provides a three terminal connection for each step or for a series of resistance steps. Specially designed lever switches separate each resistor from the others. This allows the standard to be configured in series, parallel, series-parallel, or separately without the use of external shorting bars.

Description
Precise transfer measurements up to 110 MΩ relative to a single 100 kΩ resistance standard can be obtained with the esi SR1050 High-Resistance Transfer Standards. The unit is available in two models: 1 MΩ and 10 MΩ resistance sections.

Based on a unique method for establishing known ratios, the esi SR1050 standard utilizes a transfer technique that consists of switching resistance sections in parallel, series or series-parallel sections. An outstanding design feature is a structure in which the only insulation leakage paths (other than those within each resistance section) are from the external terminals to ground. This eliminates insulation leakage errors in the transfer of calibration from one resistance level to another using three-terminal measurement techniques.

A specially designed lever switch provides a convenient means of switching into parallel and series parallel configuration without introducing insulation leakage errors. External shorting or paralleling bars are not necessary. Each resistance section consists of precision wire-wound resistors connected in series. The reduced heat concentration of the series connection improves the thermal characteristics of a resistance element with an already low temperature coefficient

Advantages of Transfer Standards
In order to perform calibrations with a high degree of accuracy, reference standards must be employed at every range or decade of the measuring or calibration instrumentation. Clearly, this can be difficult and costly since these standards must be highly stable and their precise values must be known with a high degree of certainty and sufficient resolution.

To minimize the cost and difficulty, more practical means of performing such calibrations is to use transfer standards.

If one has a single standard that is calibrated by a national laboratory, one can then compare the transfer standards to the certified standard by ratio techniques. See our Technical Applications section for a full tutorial. The Benefits of Using Transfer Standards

SPECIFICATION

SPECIFICATION

esi SR1050 Transfer Standards Basic Specifications

Transfer Accuracy Limited only by short-term repeatability of resistance values. Typical repeatability ±2 ppm
Initial Accuracy ±25 ppm of nominal value, matched within 10 ppm, for 1 MΩ, ±30 ppm of nominal value, matched within 10 ppm, for 10 MΩ
Long-Term Accuracy ±50 ppm of nominal value
Calibration Accuracy ±10 ppm for 1 MΩ; 15 ppm for 10 MΩCalibration Conditions 23 ºC, low power, three-terminal measurement
Temperature Coefficient ±5 ppm/ºC, matched within 5 ppm/ºC
Power Coefficient ±0.05 ppm/mW per resistor
Maximum Power Rating 1W/step or 5W distributed over 10 steps, or maximum voltage of 2.5 kV where this value does not result in power excess of 1W per resistor
Breakdown Voltage 5000 V peak between active terminals and case
Leakage Resistance Greater than 10 TΩ from terminals to case

DATASHEET AND MANUAL

DATASHEET AND MANUAL

  • Data Sheet: This document explains the features, options, Specifications and option models for this item.
  • Product Manual: Specifications and option models for this item. This document contains the technical product manual and guidelines.
APPLICATION NOTES AND SOFTWARE

APPLICATION NOTES AND SOFTWARE

  • Application Notes: Application notes and technical resources for this instrument.
ACCESSORIES

ACCESSORIES

ISO-17025 Accredited Calibration with Test Data

ISO-17025 ACCREDITED CALIBRATION WITH TEST DATA

TL-600 Spade Lug Cable

TL-600 PERFORMANCE SPADE LUG CABLES

Related products

VHS-Series (Wide Frequency Band Type)

M-Series (Low Acoustic Noise and Compact Range)

Charge Amplifier (VM-1980/3)

Seismic Monitoring System (SW-72R)

Seismic Monitoring System (SW-72)

K2

Seismic Monitoring System (SW-74SI)

K-Series (High Excitation Force Water Cooled Range)

CONTACT US

Hanoi Office:
Address: 5th Floor, 84 Duy Tan Street, Cau Giay District., Hanoi, Vietnam
Tel: +84 (24) 3795 9933
Fax: +84 (24) 3795 9944
Hotline: 0907910088
Email: Sales@technovietnam.com

HCM Office:
Address: No. 54, Street 6, Trung Son Area (KDC Trung Sơn), Binh Hung, Binh Chanh District, HCM
Tel: +84 (28) 5431 6377
Fax: +84 (28) 5431 6378
Hotline: 0907910088
Email: Sales@technovietnam.com

MAIN MENU

  • Home
  • About Us
  • Products
  • Partners
  • Services
  • News
  • Recruit
  • Contact Us

PRODUCT CATEGORIES

  • Reliability & Durability Test and Measurement
  • Electric & Electronic Test and Measurements
  • Industrial Machines & Automation System
  • Material Inspection and Analysis
  • Optical & Mechanical Test and Measurements
  • Other Test and Measuring Instruments
  • Parts Accessories & Consumables
  • Tools - Handtools - Industrial Tools
COPYRIGHT 2015 TECHNO VIETNAM. ALL RIGHTS RESERVED.
payments
Close
  • Home
  • About us
  • Products
  • Partners
  • Services
  • Customers
  • Recruit
  • Contact us
Shopping cart
close

Sign in

close

Lost your password?

No account yet?

Create an Account
Sidebar
Start typing to see products you are looking for.
x
x
Home
Shop
Blog
Menu